kc-interface/README.md

# DIY - Setting up the KaosCube 

1. [Hardware](#hardware)
  *  [Components](#components)
  *  [Installing the OS](#installing-the-os)
2. [Software](#software)
  *  [Upgrade the OS](#upgrade-the-os)
  *  [Setting up the Access Point](#setting-up-the-access-point)
  *  [Installing firmware of the wifi dongle](#installing-firmware-of-the-wifi-dongle)
  *  [Create network connection with new wifi dongle](#create-network-connection-with-new-wifi-dongle)
  *  [Installing the KaosCube Interface](#installing-the-kaoscube-interface)
3. [Setting up functions of the KCInterface manually](#setting-up-functions-of-the-kcinterface-manually)
  *  [Setting up the Hidden Service](#setting-up-the-hidden-service)

# Hardware

## Components

+ Orange Pi Zero
+ MiniUsb2Usb Cable for power-supply
+ An Ethernet !Crossover! Cable for ssh access
+ An MicroSD 16 GB for the Installation of the OS
+ MicroSD2Usb Reader to plug in the Laptop
+ Linux Wifi Dongle
+ Wifi Antenna
+ A laptop, preferably with Linux installed

## Installing the OS

Because Ubuntu is half proprietary, and there is a surveillance door for 
Amazon on the system, the KAOS Cube runs on ARMbian - Debian based.

First step is to partition the MicroSD
	
    lsblk		# list devices see which /dev/sdX is usb
	
    sudo fdisk /dev/sdb	# In my case, the usb is /dev/sdb
	
    Command: d		# Inside fdisk: delete all partions
	
    Command: n		# Inside fdisk: Create new Partion
			# Press enter until you are done
    Command: w		# Write the changes

    sudo mkfs.vfat /dev/sdb1 # format the new partition to fat32


Get a buster image from https://www.armbian.com/download/ for the orange pi
zero, as sshd is still running by default on the resulting machine

Now copy binarywise the image to the partition
	
    sudo dd bs=4M if=ArmbianBusterForOrangePiZero.img of=/dev/sdb


Thats it! The free system should be installed. Put the MicroSD into your OrangePi.

Now connect the cables. The Orange Pi will boot by supplying it with 
power.

Connect your computer with ethernet (crossover, special one) cable to the orange pi zero.
The first boot takes a bit longer, up to 2 minutes.


On the Armbian System, SSH on ethernet is enabled. We need to give the 
Pi an IP Adress now.

    # Install a dhcp client, in my case it was Arch and dhcpd
    sudo pacman -S dhcpd

Now we have to create a new local network.
The easiest way is to go into your graphical network-manager. Select the 
ethernet connection to your Pi and go on settings.

In my case I went to IPv4 settings. Then I selected "Shared to other 
computers" Method. After this add a new Address:

    Address 10.0.0.1	# The 10.0.0.1 Number is normally used for local 
    			# networks.
    Netmask 24		# You can also put in 255.255.255.0, which only 
    			# says to the dhcp to give a certain range of 
    			# adresses starting at 10.0.0.0
    Gateway 10.0.0.1	# The Gateway is the adress of your laptop 
    			# itself


Now you can run the command 
    sudo arp -a

in your bash, after restarting the connection over ethernet to your Pi.

On your Orange Pi, the small green Light close to the mini usb port 
should be lighting. If the connection is established, you should see it 
blinking. If one or both are not the case, try to reinstall the ARMbian 
image, or zero the first part of the partition, maybe it was not booting 


You will see an assigned IP Adress on your ethernet interface, on arch 
for me it was the standard one enp0s25

The IP was 10.0.0.254, so I could connect through ssh with my Orange 
Pi now, and start to set up the system.

    ssh root@10.0.0.254


If everything worked, type in 1234 as the password and follow the instructions.

If not, check out 
https://docs.armbian.com/User-Guide_Getting-Started/#how-to-prepare-a-sd-card

For example, you can learn there how to verify the hash of your download, to be sure nobody
gave you a virus instead of an OS :)


# Software

## Upgrade the OS


In the newer versions of armbian, ssh is deactivated by default.
To save time, we installed an armbian buster.
Generally, it is important to keep your KaosCube up to date.
That is why, after getting access to the Cube, the first thing is 
an upgrade to bullseye (which is debian stable at the time of this 
writing and has the latest debian-security updates inside)

    sudo apt update
    
    sudo apt dist-upgrade -y

Then change the apt configuration file

    sudo nano /etc/apt/sources.list

and change all words which are "buster" to "bullseye".

Except of the line regarding debian-security. There, you have
to change "buster" to "bullseye-security".

Save (in nano that is strg+o) and exit nano (strg+x)

Then update with the new list and run the upgrade

    sudo apt update

    sudo apt upgrade

During the upgrade, always choose ok or default :).

Then go to /etc/apt/sources.list.d/armbian.list and change to bullseye there too
Then run again the update and upgrade.


## Setting up the Access Point


    nmcli con add type wifi ifname wlan0 mode ap con-name kaoscube ssid KaosCube ipv4.method shared
    nmcli con modify kaoscube wifi-sec.key-mgmt wpa-psk
    nmcli con modify kaoscube wifi-sec.psk "ThePasswordYouLike"
    nmcli con up kaoscube


## Installing firmware of the wifi dongle

First thing to do is updating the apt ressources

    sudo apt update

Then install git

    sudo apt install git

Install dkms

    sudo apt install dkms

Install the newest headers

    sudo apt-get install linux-headers-current-sunxi build-essential

When installing build-essential, you will be prompted whether to restart
or not. Enter no automatic restart and then for cron and ssh enter ok.
For the ssh config, I kept the old one.
after the install, restart the system with

    sudo reboot

Now download the firmware

    git clone https://github.com/kelebek333/rtl8188fu

Now go to the folder rtl8188fu. Add, build and install it with dkms

    sudo dkms add ./rtl8188fu
    sudo dkms build rtl8188fu/1.0
    sudo dkms install rtl8188fu/1.0
    sudo cp ./rtl8188fu/firmware/rtl8188fufw.bin /lib/firmware/rtlwifi/

After all commands have run successfully, restart the system

    sudo reboot

##Create network connection with new wifi dongle

First look up with ifconfig for the interfaces, and which one is the one of the dongle

    sudo ifconfig

there should be one called wlan0 or wlan1, which is the small one already on the orange pi zero.

In addition, there should be one with the name wlx00... something.

This one you should use with the following command:

    nmcli device wifi connect 'FRITZ!Box 6430 Cable TL' password "98475637998946115486" ifname wlan0



##Installing the KaosCube Interface

First add a new user, if you are still root:

    adduser kaosuser

Then add the user to sudoers:

    usermod -aG sudo kaosuser

Now change to user (still being root) and go to home directory

    su kaosuser
    cd



First clone the interface from git:

    git clone https://code.basabuuka.org/alpcentaur/kc-interface.git


After that, install php (working version is 7.4, but newer ones should 
also work)

    sudo apt install php


Also the interface needs the following libraries:

    sudo apt install tor

Now go in the directory kc-interface and run

    bash startserver.sh

You will have the interface running on localhost:666

To get the interface, connect to the ap kaoscube and enter the 
IP of its wifi interface with a double point and then 666.

# Setting up functions of the KCInterface manually

## Setting up the Hidden Service

First install Tor:

	sudo apt-get install tor

Edit the torrc file:
	
	sudo nano /etc/tor/torrc


Look for the line ############### This section is just for location-hidden services ###

under this line, enable (uncomment) HiddenServiceDir and HiddenServicePort

in our case, 

    HiddenServiceDir /var/lib/tor/hidden_service/
    HiddenServicePort 80 127.0.0.1:80
    HiddenServicePort 22 127.0.0.1:22


After restarting tor with

    sudo systemctl restart tor


your hidden service is running, and you can get its address under 
/var/lib/tor/hidden_service/ , or whatever name or path you wrote in
the torrc.